AKCP ropeWater Sensor (RWS10)
Detect water leaks over large area
- Ideal for covering large areas
- Compatible with sensorProbe and securityProbe series
- Protect water sensitive equipment from potential disaster
- Notifications via E-mail, SNMP trap, SMS and more
- Comes in extendable 10ft lengths, or pre order custom length
- Powered by the sensorProbe/securityProbe base unit, no additional power required
- Will report critical state if cable is cut or damaged
With the ropeWater sensor you can protect your essential equipment from potentially harmful water damage. Designed and manufactured by AKCess Pro it forms an integral part of your disaster prevention system.
Ideal for use in basements and under false floors and roof spaces, the ropeWater sensor can cover a large area. Combined with any of the sensorProbe series or securityProbe series units it will give you advance notice of any water leaks or flooding.
The sensor will retain it?s error condition until it is read via an SNMP get. Therefore if the sensor encounters a critical condition at anytime it will report that condition before it returns to a normal state.
The AKCP ropeWater sensor is a rope type water detector designed for ecient water detection monitoring.
The ropeWater sensor can be connected to any one of the sensorProbe or securityProbe´s RJ-45 Intelligent Sensor ports enabling the unit to detect the presence or non-presence of water.
This water sensor is a switch type that will be on or o and will detect the presence of water if any portion of the rope becomes wet.
This sensor comes fully assembled including the Water sensing rope, the non-sensing cable that connects the rope to the sensing module and the main sensing module that connects via CAT5 LAN cable to the sensorProbesecurityProbe 5E
The sensing rope cable can be pre-ordered from a 10 foot minimum to any custom run length of up to 165 feet or 50 meters . The non-sensing cable comes in a standard 20 foot run length.
The sensing module is then connected to any of the RJ-45 Intelligent sensor ports on the AKCP base units using standard CAT5/6 LAN cable.
The presence, or non-presence of water can be used to trigger alerts like e-mail, SMS, phone calls and SNMP traps. The sensor has its own SNMP OID so that it can be monitored over your network using any Network Management System.
Each ropeWater sensor comes complete with a 5 foot sensor cable that connects the main sensing module to either the sensorProbe or the securityProbe?s RJ-45 sensor ports, or you can use your own CAT5e/6 LAN cable. This cable can be extended up to 100 feet or 30 meters.
Ideal for use in basements and under false oors and roof spaces, the ropeWater sensor can cover a large area. Combined with any of the sensorProbe series or securityProbe series units it will give you advance notice of any water leaks or ooding. The sensor will retain its error condition until it is read via an SNMP get. Therefore if the sensor encounters a critical condition at anytime it will report that condition before it returns to a normal state.
Ideal for use in basements and under false floors and roof spaces, the ropeWater sensor can cover a large area. Combined with any of the sensorProbe series or securityProbe series units it will give you advance notice of any water leaks or flooding.
The sensor will retain it?s error condition until it is read via an SNMP get. Therefore if the sensor encounters a critical condition at anytime it will report that condition before it returns to a normal state.
The AKCP ropeWater sensor is a rope type water detector designed for ecient water detection monitoring.
The ropeWater sensor can be connected to any one of the sensorProbe or securityProbe´s RJ-45 Intelligent Sensor ports enabling the unit to detect the presence or non-presence of water.
This water sensor is a switch type that will be on or o and will detect the presence of water if any portion of the rope becomes wet.
This sensor comes fully assembled including the Water sensing rope, the non-sensing cable that connects the rope to the sensing module and the main sensing module that connects via CAT5 LAN cable to the sensorProbesecurityProbe 5E
The sensing rope cable can be pre-ordered from a 10 foot minimum to any custom run length of up to 165 feet or 50 meters . The non-sensing cable comes in a standard 20 foot run length.
The sensing module is then connected to any of the RJ-45 Intelligent sensor ports on the AKCP base units using standard CAT5/6 LAN cable.
The presence, or non-presence of water can be used to trigger alerts like e-mail, SMS, phone calls and SNMP traps. The sensor has its own SNMP OID so that it can be monitored over your network using any Network Management System.
Each ropeWater sensor comes complete with a 5 foot sensor cable that connects the main sensing module to either the sensorProbe or the securityProbe?s RJ-45 sensor ports, or you can use your own CAT5e/6 LAN cable. This cable can be extended up to 100 feet or 30 meters.
Ideal for use in basements and under false oors and roof spaces, the ropeWater sensor can cover a large area. Combined with any of the sensorProbe series or securityProbe series units it will give you advance notice of any water leaks or ooding. The sensor will retain its error condition until it is read via an SNMP get. Therefore if the sensor encounters a critical condition at anytime it will report that condition before it returns to a normal state.
Specifications
Measurement Range
Measurement Accuracy
Sensor Type
Power Consumption
Communications Cable
Sensor OID
Note
Ordering Information
Measurement Range
- Wet or Dry (-20 degrees C- +60 degrees C)
Measurement Accuracy
- Able to detect the presence or non-presence of water
Sensor Type
- Patent pending, capacitance measurement technology
Power Consumption
- Typical 125 mWatt, 25 mA
Communications Cable
- RJ-45 jack to main sensor module using UTP CAT5 cable. Maximum extension cable run length is 30 meters (100 feet).Comes fully assembled including the Water sensing rope, the non-sensing cable that connects the rope to the sensing module and the main sensing module that connects via CAT5 LAN cable to the sensorProbe / securityProbe 5E.Sensing rope cable can be pre-ordered from a 10 foot minimum to any custom run length of up to 165 feet or 50 meters.
- Non-sensing cable comes in a standard 20 foot run length.
Sensor OID
- .1.3.6.1.4.1.3854.1.2.2.1.18.1.3.0
Note
- AKCP does not recommend the ropeWater Sensor to be placed on a conductive surface.
Ordering Information
Product Model | Order Number | Descrition |
---|---|---|
Rope Water Sensor | ||
V2RWSC10 | 10ft Rope Water Sensor (no extension capability) | |
RWSC10 | 949019 | 10ft Rope Water Sensor (with extension capability) |
RWSCCAB10 | 940033 | 10ft extension cable for RWSC10 and LWSC10 |
RWSCCABXX | 940087 | Extension (1 metre) |
Customers who viewed this item also viewed